Interior Film
Interior
Piano-black trim scratches if you look at it. Touchscreens collect key marks and fingernail lines. Interior is a thinner 6.3 mil clear film that lays flat over trim, screens and door cups without bulking up an edge or lifting at a corner — the same clarity as Master, in a gauge that suits an interior.
- 6.3 mil / 160 µm
- Clear, high gloss
- 10-year warranty
- Self-healing
- 160 µm total thickness
- 6.3 mil
- Tensile strength
- ≥ 34.3 MPa
- Limited warranty
- 10 yr
Order
Buy Interior
Purpose-cut for the surfaces inside the car that scratch fastest and cost the most to replace.
- Piano-black center consoles
- Infotainment and instrument screens
- Door cups and sill plates
- Kick panels and loading lips
$300
Why this film
What Interior is for
Purpose-cut for the surfaces inside the car that scratch fastest and cost the most to replace.
Made for gloss-black trim
The single most scratch-prone surface in a modern car. Interior covers it invisibly, and takes the marks that would otherwise be permanent.
Thin enough for a screen
6.3 mil lays down without a visible bezel edge or a change in touch response on an infotainment display.
Self-healing topcoat
The topcoat is an elastomeric, lightly crosslinked surface. Warm it and the polymer chains regain enough mobility for the network's own elasticity to pull a light swirl back out — the deformation was stored, not removed. Wash marks close instead of collecting into a season of haze.
Sells the job you are already doing
An interior kit is the easiest add-on in a PPF shop: same customer, same appointment, no extra bay time.
Specification
Interior by the numbers
Production-lot values from the HAUT technical data sheet for this film, each with the ASTM method it was measured against.
| Thickness | 160 ±15 µm / 6.3 milISO 4593 |
|---|---|
| Gloss at 60° | ≥ 92 %ISO 2813 |
| Tensile strength | ≥ 34.3 MPaISO 527-1 |
| Elongation at break | ≥ 250 %ISO 527-1 |
| Peel adhesion | ≥ 21 N/25 mm at 180°, 24 hISO 29862 |
| Initial tack | ≥ 12 N/25 mmFINAT FTM 9 |
| Liner release force | ≤ 0.35 N/25 mmISO 29862 |
| Shrinkage | ≤ 0.5 mm MD · ≤ 0.4 mm TDFINAT FTM 14 |
| Water contact angle | ≥ 103°DL/T 864 |
| Yellowness index | ≤ 2QUV |
| Self-healing activates at | 50 °C surfaceBrush & heat |
| Maximum temperature | 120 °C for ≥ 5 minGB/T 2423 |
| Warranty | 10 years |
Values are from the technical data sheet for each film. Testing is carried out at the production line to the standards listed — national methods that are adoptions of the ISO standards named on the test-methods page. Where an ASTM method is equivalent it is given there for reference; no value on this site has been re-run to ASTM, and we do not print an ASTM code as though it had been. Where a film has no measured value for a property, the row is left out rather than filled in.
How Interior differs
Interior is the only film in its family, so there is nothing in the HAUT range to compare it against directly — the comparison that matters is against whatever you are using today, and every property we have measured is in the table beside this.
Every HAUT film carries a 10-year limited warranty against cracking, delamination and blistering when installed by a certified shop and registered online.
Get it installed
HAUT film is installed by certified shops only — that is what makes the 10-year warranty enforceable. Find one near you, or if you run a shop, apply to carry the line.